White Westinghouse Washer WM50T 1 User Manual

LAVABIANCHERIA  
MANUALE DELL’UTENTE  
WASHING MACHINE  
USER MANUAL  
mode d’emploi de machine  
à laver électronique  
 
THE CONTENTS  
SECTION 1:BEFORE USING  
Safety warnings  
Recommendations  
SECTION 2:INSTALLATION  
Removal of transportation screws  
Adjustment of feet  
Electrical connection  
Water supply connection  
Water drain connection  
SECTION 3:TECHNICAL SPECIFICATIONS  
SECTION 4:CONTROL PANEL  
Start/Pause button  
Function indicator lights  
Function buttons  
Spin speed selector  
Program knob  
SECTION 5:WASHING YOUR LAUNDRY  
Before washing  
Running the machine  
SECTION 6:MAINTENANCE AND CLEANING  
Water inlet filters  
Pump filter  
Detergent drawer  
Siphon plug  
The cabinet  
The drum  
Remove of your machine from lime  
SECTION 7: PRACTICAL INFORMATION  
SECTION 8:AVOIDING MINOR FAULTS  
SECTION 9:AUTOMATIC FAILURE DETECTION SYSTEM  
SECTION 10:INTERNATIONAL WASHING SIGNS  
28  
 
SECTION 1:BEFORE USING  
SAFETY WARNINGS  
Do not use a multiple socket or extension cord.  
Do not insert a plug with damaged or broken cord into the socket.  
If the cord is damaged it should be replaced by the manufacturer or  
appointed service agent in order to avoid a hazard.  
Never remove the plug from the socket by pulling from the cord  
section. Remove the plug by holding.  
Do not plug the power supply with wet hands.  
Never touch the machine with wet hands or feet.  
Never open the detergent drawer while the device is running.  
Never force to open the door of the machine while the machine is  
running.  
Since the machine can reach high temperatures while running, do not  
touch the drain hose and water during draining.  
In case of any failure, first unplug the device and close the water tap.  
Do not attempt to repair.Please apply to the nearest authorized  
service station.  
Do not forget that the packing material of your machine may be  
hazardous for children.  
Do not let your children play with the washing machine.  
Keep your pet away from your machine.  
Your machine should only be used by adults within the information  
written in this manual.  
Your machine is designed for use in house environment. Warranty  
will be invalid if you use it for commercial purposes.  
The appliance should not be put on a carpet which can block the air  
ventilation on the bottom side.  
RECOMMENDATIONS  
The detergent or softener in contact with air for a long time will dry  
and stick to your detergent drawer.To avoid this put your detergent  
and softener into the detergent drawer just before washing.  
It is recommended that you use pre-washing program for only very  
dirty clothes.  
Please do not exceed the maximum loading capacity.  
Download from Www.Somanuals.c2om9. All Manuals Search And Download.  
If you will not use your machine for a long time, unplug your machine,  
close the water supply and leave the door open in order to keep the  
inside of the machine dry and for prevention from unpleasant odour.  
As a result of the quality control procedures, a certain amount of  
water may remain in your machine. This is not harmful for your  
machine.  
SECTION 2: INSTALLATION  
You must pay attention to the following issues before using your washing  
machine.  
REMOVAL OF TRANSPORTATION SCREWS  
Transportation screws, which are located at the back side of the  
machine, must be removed before running the machine.  
Loosen the screws by rotating counterclockwise by a suitable wrench.  
(DIAGRAM-1)  
Remove the screws by pulling them.(DIAGRAM-2)  
To the holes where the transport screws have been removed, insert  
the plastic transport screw taps found in the accessories bag.  
(DIAGRAM-3)  
The transportation screws, that have been removed from the machine  
should be kept in hand for any other transportation necessities.  
DIAGRAM-2  
DIAGRAM-1  
DIAGRAM-3  
ADJUSTMENT OF FEET  
Do not install your machine on rugs or similar surfaces.  
For your machine to work silently and without any vibration, it should  
be settled on a flat, non-slippery and tough ground.  
 
30  
You can adjust the balance of your machine from its feet.  
First, loosen the plastic adjustment nut.  
Adjust by rotating the feet upwards or downwards.  
After the balance has been reached, tighten the plastic adjustment  
nut again by rotating it upwards.  
Never put cartons, wooden blocks or similar materials under the  
machine to balance the irregularities on the level of the ground.  
ELECTRICAL CONNECTION  
Your washing machine works with 220-240V and 50Hz.  
A special grounded plug has been attached to the network cable of  
your washing machine. This plug must definitely be inserted to a  
grounded socket with 10 ampere. The fuse flow value of the  
electricity line attached to this should also be 10 ampere. If you have  
no such sockets and fuses in your house, let it be made by a qualified  
electrician.  
Our company will not be responsible for any damages that may  
occur as a result of usage without grounding.  
WATER SUPPLY CONNECTION  
Your machine has a single water (cold) inlet.  
To prevent from the leakages on the connection joints, 1 seal is  
included in the hose packing.(Fit this seal on the end of the water  
inlet hose at the tap side.)  
Connect the end with bracket of the water inlet hose to the water inlet  
valve at the rear of the machine and the other end to your tap. In  
situations where you are not assured, let a qualified plumber make  
the connection works.  
Water pressure of 1-10 bars from your tap will enable your machine  
to work more efficiently.(1 bar pressure means water flow of more  
than 8 liters in 1 minute from a fully opened tap).  
After connections are completed, check for the non-leakage of the  
connection joints by turning on your tap completely.  
Be sure that water inlet hoses are not folded, broken or crushed.  
Mount the water inlet hoses to a 3”/4, geared water tap.  
31  
 
Cold water inlet  
WATER DRAIN CONNECTION  
Be sure that water inlet hoses are not folded, twisted, crushed or  
elongated by stretching.  
Water drain hose should be mounted at a height of minimum 60 cm,  
maximum 100 cm from the ground.  
The end of the water drain hose may directly be fitted to the dirty  
water outlet hole or a special apparatus mounted on the outlet  
bracket of the wash-stand.  
Never attempt to extend the water drain hose by adding extra parts.  
32  
 
SECTION 3:TECHNICAL SPECIFICATIONS  
WM50T-1  
Maximum dry laundry capacity (kg)  
5
Recommended loading (kg)  
Height (cm)  
4,5  
85  
Width (cm)  
59,6  
Depth (cm)  
51  
Maximum spin cycle ( rpm )  
500  
(*) Maximum spin cycles depend on the model you’ve chosen  
1
2
3
4
5
6
7
1-Upper tray  
2-Detergent drawer  
3-Control panel  
4-Door  
5-Handle  
6-Filter cover  
7-Kickplate  
33  
 
SECTION 4:CONTROL PANEL  
WM50T-1  
1
2
3
4
5
6
7
8
9
1-Detergent drawer  
2-Start/pause light  
3-Function indicator lights  
4-Temperature adjustment knob  
5-Program ready light  
6-Program knob  
7-Start/pause button  
8-Function buttons  
9-Program end light  
34  
 
START/PAUSE BUTTON  
Used to start a selected program or pause during running.  
WARNING!  
It is required for the program knob to be brought to O(off)  
position before selecting the program or changing a continuing  
program.  
FUNCTION INDICATOR LIGHTS  
When the start/pause button or any function button is pressed,the  
corresponding light turns on.The light turns off when the function  
button or start/pause button is re-pressed, or when the process  
the selected function is completed.  
The function indicator lights are also used in failure detection system  
mentioned in section 9.  
FUNCTION BUTTONS  
No spin  
This program is recommended to be used for your sensitive  
clothes on which no spinning should be done. By pressing this  
function button, you can cancel the spinning process which is  
included in the program.  
Easy ironing  
By using this function, you can ensure your clothes to come out  
less wrinkled after the washing.  
35  
 
WARNING!  
Functions vary depending on the model you have chosen.If you  
forgot to use additional function and your machine starts to wash  
push the additional function button if the indicator light is on.  
Additional function will be activated.If the indicator light is not  
on,additional function will not be activated.  
TEMPARATURE ADJUSTMENT KNOB  
By the temparature adjustment knob, you can adjust the washing water  
temparature of your clothes between O(cold wash) and 90 ˚C. When you are  
selecting the washing water temparature, pay attention to the international  
washing signs on your clothes.  
PROGRAM KNOB  
With the program knob, you can select the program with which you desire to  
wash your clothes. You can adjust the program selection process by turning  
the program knob in both directions. You must be careful that the adjustment  
sign of the program knob is exactly on the program you want to select. When  
you bring the program knob to O(off) position, while your machine is running,  
your program will remain incomplete.  
36  
 
1-Cotton 90°C  
2- Cotton 60°C with prewash  
3- Cotton 60°C  
4- Cotton 40°C  
5- Eco wash  
6- Quick wash  
7- Cotton cold  
8- Synthetic 60°C  
9- Synthetic 40°C  
10- Synthetic cold  
11- Delicate 30°C  
12- Wool 30°C  
Rinsing  
Spin  
Draining  
OFF  
SECTION 5: WASHING YOUR LAUNDRY  
Plug the machine.  
Open the tap water.  
First wash cycle  
There may be water left inside your machine after factory tests and trials.It is  
recommended that the first wash cycle should be made without any laundry  
so that carry out this water; pour half a measuring cup of normal allpurpose  
detergent into compartment 2 and select cotton program at 90°C.  
BEFORE WASHING  
Discrimination of your laundry  
Discriminate your clothes according to their types (cotton, synthetic,  
sensitive, woolen, etc.),washing temperatures and level of dirtiness.  
Never wash your white and coloured clothes together.  
Since your new coloured clothes may shed dye on the first wash,  
wash them separately.  
Be careful that no metal pieces are found on or in the pockets of your  
clothes, remove if there is any.  
Zip and button your clothes.  
Remove the plastic or metal hooks of the curtains and laces or place  
them inside a washing bag and tie.  
37  
 
Pull the textiles like trousers,knitted fabric,t-shirt and sweat shirt  
inside out.  
Wash your small clothes like socks and handkerchiefs in a washing  
bag.  
Wash up tol 90 ˚C Wash up to 60 ˚C Wash up to 30 ˚C Not washable in  
washing machine  
Placement of the clothes into the machine  
Open the door of your machine.  
Fill your clothes in your machine in a well-spread manner.  
Place each cloth separately.  
When you shut the door of your machine, be careful that no cloth is  
jammed between the cover and the gasket.  
Shut the door of your machine tightly otherwise your machine will not  
start the washing process.  
Filling detergent in the machine  
The quantity of the detergent that you will fill in your machine depends on the  
following criteria:  
Your detergent consumption will change according to the dirtiness  
level of your clothes. For your slightly dirty clothes, do not pre-wash  
and put a small amount of detergent in the compartment no.2 of the  
detergent drawer.  
For your excessively dirty clothes, select a program with pre-  
washing, fill ¼ portion of the detergent you will put in compartment  
1 in the detergent drawer and the remaining portion in compartment  
2.  
In your machine,use the detergents developed especially for  
automatic washing machines. The quantities that will be used for  
your clothes are written on the packing of the detergents.  
As the hardness of your water increases, the amount of the  
detergent to be consumed will also increase.  
As the amount of your clothes increases, the amount of the  
detergent to be consumed will also increase.  
Fill your softener in the softener compartment in your detergent  
drawer. Do not exceed the MAX level. Otherwise, the softener will  
diffuse in the washing water via the siphon.  
The softeners with high density should be diluted with some water  
before filling in the drawer. That is because the softener with high  
density obstructs the siphon and prevents the flow of the softener.  
38  
 
You can use fluid detergents in all programs without pre-washing.  
For this, mount the fluid detergent level plate in the second  
compartment of the detergent drawer and arrange the amount of  
fluid detergent according to the levels on this plate.  
RUNNING THE MACHINE  
Program selection and features  
Select the program and additional functions appropriate for your clothes from  
Table-1.  
Start/Pause  
By pressing this button, you can start the program you have selected or  
pause a running program.  
Starting the program  
Adjust the program knob to a program you desire.  
The program ready light will be on.  
If you want, you can select one or more additional functions.  
Run the program which you have selected by pressing the  
Start/Pause button.  
Changing the program  
If you have selected a program and you do not want if to continue:  
Press the start/pause button.  
Bring the program knob to O(off) status.  
Adjust the program knob to the program you desire.(You can select  
the program that you desire from Table-1).  
The program ready light will be on.  
By pressing the start/pause button, run the program which you have  
selected.  
Cancellation of the Program  
If you desire to end a running program early:  
Press the start/pause button.  
Turn the program knob to O(off) status.  
Turn the program knob to “Draining” or “Spinning” programs.  
The program ready light will be on.  
Run the program you have selected by pressing the start/pause  
button.  
Program ending  
Your machine will automatically stop when the program you have  
selected ends.  
The program end light will be on.  
Turn the program knob to O(off) position.  
39  
 
The door will be unlocked in approximately two minutes after the  
program ends.You can open the door by pulling the handle of the  
door towards yourself and take out your clothes.  
After you unload your clothes leave the door open to dry the interior  
of your machine.  
Unplug your machine.  
Close the water tap.  
WARNING!  
If the power is off end on again after a while on any stage of the washing  
program, your machine will continue the program from the point where it was  
interrupted. This is not harmful for your machine.  
Child lock  
The Child Lock prevents unauthorised changes on the control panel while the  
machine is in operation. The child lock will be activated after the start/pause  
button on the control panel is pressed for a period longer than 2 seconds. To  
inactivate it, you have to press the same button for a period of longer than 2  
seconds. At the end of the program, take the program knob to the “0” point for  
canceling the “Child Lock” option.  
WARNING!  
Your machine will inactivate the spin speed selector and function buttons  
when the child lock is activated.  
SECTION 6: MAINTENANCE AND CLEANING  
Unplug your machine.  
Close the water tap.  
WATER INLET FILTERS  
On the tap part of your machine’s water inlet hose and at the ends of water  
inlet valves, there are filters to prevent entrance of the dirt and foreign  
materials in the water to the machine. If the machine is unable to receive  
sufficient water although your water tap is opened, these filters should be  
cleaned.  
40  
 
MAX DRY LOAD  
CAPACITY (kg)  
DETERGENT  
COMPART.  
ADDITIONAL FUNCTION  
BUTTON  
PROGRAM  
TYPE OF LAUNDRY  
EXPLANATIONS  
WM50T-1  
Dirty, boil, cotton and linen  
textile  
1-COTTON 90˚  
2
1+2  
2
5
2-COTTON 60˚  
(PREWASH)  
Very dirty, cotton, coloured  
and linen textile  
5
5
Underwears, sheet,  
table cloth, t-shirt,  
shirt, towel  
Dirty, cotton, coloured and  
linen textile  
3-COTTON 60˚  
Slightly dirty, paint to get  
out, cotton, coloured and  
linen textile  
4-COTTON 40˚  
2
5
5-ECO  
WASH  
Dirty, cotton, coloured and  
linen textile  
2
2
5
Slightly dirty, cotton,  
coloured and linen textile  
Slightly dirty cotton,  
coloured and linen textile.  
Washed without heating the  
tap water.  
6-QUICK WASH  
2,5  
7-COTTON  
COLD  
2
5
Dirty, synthetic or synthetic  
mixture textile  
Nylon socks, blouse  
Nylon socks, blouse  
8-SYNTHETIC 60˚  
9-SYNTHETIC 40˚  
2
2
3
3
Slightly dirty, synthetic or  
synthetic mixture textile  
Slightly dirty, synthetic or  
synthetic mixture sensitive  
laundry.Washed without  
heating the tap water.  
Slightly dirty, cotton,  
coloured, synthetic or  
synthetic mixture sensitive  
laundry  
10-SYNTHETIC  
COLD  
Nylon socks, blouse  
2
3
Silk mixture, shirt,  
blouse, polyester,  
poliamid, mixture  
textile  
11-DELICATE 30˚  
12-WOOL 30˚  
2
2
Dirty, hand and machine to  
wash wool laundry  
All wool laundry  
TABLE-1  
 
MAX DRY LOAD  
CAPACITY (kg)  
DETERGENT  
COMPART.  
ADDITIONAL FUNCTION  
BUTTON  
PROGRAM  
TYPE OF LAUNDRY  
EXPLANATIONS  
WM50T-1  
When you need an additional rinsing to be done to your clothes after the washing process, you can use this program for all kinds of clothes.  
RINSING  
When you need an additional spinning to be done to your clothes after the washing process, you can use this program for all kinds of  
clothes.  
SPINNING  
This program is used to drain the dirty water inside after the washing process of your machine. If you want the water inside your machine to  
be drained before the program ends, you can use this program.  
DRAINING  
TABLE-1 CONTINUE  
(*) You can use softeners in all programs (except spinning and draining programs) optionally. When you arrange the quantity of the softener, comply with the warning of  
the softener producer. Fill your softener in its  
(softener) compartment of the detergent drawer.  
 
Remove the water inlet hose.  
Remove the filters found on the water inlet valves by using a pincer  
and wash thoroughly with a brush.  
Clean the filters of the water inlet hoses located on the tap side by  
removing manually together with the seal.  
After you clean the filters, you can fit them the same way as you have  
removed.  
PUMP FILTER  
The pump filter system elongates the life of your pump, which is used to drain  
the dirty water. It prevents lint to enter the pump. Cleaning of your pump filter  
in every 2-3 months is recommended. To clean your pump filter:  
Remove the kickplate by pushing with your hand upwards from the  
lower claws and pulling towards yourself.  
Before opening the filter cover,place a cup in front of the filter cover  
to prevent flow of the remaining water in the machine.  
Loosen the filter cover by rotating it counter clockwise and drain the  
water.  
Remove the foreign materials from the filter.  
Check for the rotation of the pump manually.  
After you have cleaned the pump, fit the filter cover by rotating  
clockwise.  
Fit in the kickplate by holding from the claws and push it.  
Do not forget that if you do not fit in the filter cover properly, it will  
leak water.  
Download from Www.Somanuals.c4om3. All Manuals Search And Download.  
WARNING!  
Danger of being scalded!  
Since the water inside the pump maybe hot, wait for it to cool.  
DETERGENT DRAWER  
Detergents may form a sediment in your detergent drawer or in housing of the  
detergent drawer in time. To clean the sediment, pull out the detergent drawer  
from time to time.To pull out the detergentdrawer:  
Pull the detergent drawer to the end.(DIAGRAM-1)  
Lift the front of the drawer, continue to pull until the drawer is pull  
out.(DIAGRAM-2)  
Wash will an old toothbrush and excessiveamount of water.  
Take off the leftover detergent avoid to drop into your machine.  
After drying the detergentdrawer put into the housing in the same manner  
you pull out.  
DIAGRAM-1  
DIAGRAM-2  
44  
 
SIPHON PLUG  
Pull out the detrgent drawer. Remove the siphon plug and clean the residues  
of the softener thoroughly. Fit the cleaned siphon plug in its location. Check if  
it placed properly.  
THE CABINET  
Clean the exterior surface of the cabinet of your machine with lukewarm water  
and a cleaning substance that will not irritate the cabinet. After rinsing with  
clean water, wipe it with a soft and dry cloth.  
WARNING!  
If the machine is installed in a location where the ambient temperature can fall  
below 0 ˚C, do the following when it will not be in use:  
Plug in the machine.  
Close the water tap and pull out the water inlet hose or hoses from  
the tap.  
Place the ends of the water drain and water inlet hoses in a cup on  
the ground.  
Adjust the program knob to “Draining” program.  
The program ready light will be on.  
Run the program by pressing the start/pause button.  
Unplug your machine when the program is over (program end light is  
on).  
When you complete these proces, the remaining water inside the machine will  
be drained and thus formation of ice in the machine will be prevented. When  
you operate your machine again, be sure that the ambient temperature is  
above 0 ˚C.  
THE DRUM  
Do not leave metal parts like needles, staples or coins inside your machine.  
These pieces cause formation of rust stains in the drum. To eliminate these  
stains of rust, use a cleaning substance without chlorium and follow the  
warnings of the cleaning substance producer. For cleaning of the rust stains,  
never use dish-washing wires or similar rough objects.  
REMOVE OF LIME FROM YOUR MACHINE  
If you arrange the amount of the detergent you use in your machine properly,  
there will be no need for lime removal. However, if you desire to apply the  
removal procedure, use the lime protectors in the market and pay attention to  
their warnings.  
WARNING!  
The lime eliminating substances contain acids and this may cause colour  
modifications in your clothes along with an adverse effect on your machine.  
45  
 
SECTION 7:PRACTICAL INFORMATION  
Alcoholic beverages: The stain point, should first be washed  
with cold water, than should be wiped with glycerine and water  
and be rinsed with water mixed with vinegar.  
Shoe Polish: The stain should be slightly scratched without  
ruining the cloth, rubbed with detergent and rinsed. In case it is not  
eliminated, it should be rubbed with 1 unit of pure alcohol (96  
degrees) mixed in 2 units of water and then washed with  
lukewarm water.  
Tea and coffee: Stretch the stained area of your cloth on the top  
of a container and pour water as hot as the type of your cloth can  
endure on it. If the type of your cloth is suitable,wash it with lye.  
Chocolate and cocoa: By leaving your clothes in cold water and  
rubbing with soap or detergent, wash it in the highest temperature  
that the type of your cloth can endure. If there is still a stain of oil  
left, wipe with oxygenated water (in proportion of 3%).  
Tomato paste:After scraping the dried pieces without ruining the  
cloth, leave in cold water for about 30 minutes and wash by  
rubbing with detergent.  
Meat broth-egg: Eliminate the dried stain residues and wipe with  
a sponge or soft cloth wetted in cold water. Rub with detergent  
and wash with diluted lye.  
Grease and oil stains: First wipe the residues. Rub the stain with  
detergent and then wash with lukewarm soapy water.  
Mustard: First apply glycerine to the stained area. Rub with  
detergent and then wash. If the stain still does not disappear, wipe  
with alcohol (On synthetic and coloured cloth, a mixture of 1 unit  
alcohol, 2 units water should be used)  
Blood stain: Lay your clothes in cold water for 30 minutes. If the  
stain still does not disappear, lay in mixture of water and ammonia  
(3 table-spoons of ammonia in 4 liters of water)for 30 minutes.  
Cream, ice-cream and milk: Lay your clothes in cold water and  
rub the stained area with detergent. If the stain has still not  
disappeared, apply lye on the fabric of your clothes in proper  
proportion.(Do not use lye on coloured clothes.)  
46  
 
Mould: Mould stains should be cleaned as soon as possible. The  
stain should be washed with detergent, and if it does not  
disappear, it should be wiped with oxygenated water (in  
proportion of 3%).  
Ink: Hold the stained area under cold water and wait until the inky  
water completely runs off. Then rub with water diluted with lemon  
juice and detergent, wash after waiting for 5 minutes.  
Fruit: Stretch the stained area of your clothes on the top of a  
container and pour cold water on it. Do not pour hot water on the  
stain. Wipe with cold water and apply glycerine. Wait for 1-2 hours  
and rinse after wiping with a few drops of white vinegar.  
Grass stain: Rub the stained part with detergent. If the type of  
fabric is suitable for use of lye, wash it with lye. Rub your woolen  
clothes with alcohol.(For coloured ones, a mixture of 1 unit pure  
alcohol and 2 units of water).  
Oil Paint:The stain should be eliminated before it dries by  
applying thinner on it. Then it should be rubbed with detergent and  
washed.  
Burnt stain: If your cloth is suitable for use of lye, you can add lye  
into your washing water. For woolen fabric, a cloth damped in  
oxygenated water should be covered on the stain and it should be  
ironed with a dry cloth on it. It should be washed after rinsing well.  
SECTION 8: AVOIDING MINOR FAULTS  
All repairing which must be done on the machine should be done by  
authorized service. When a repairing is required for your machine or you are  
unable to eliminate the failure with the help of the information given below:  
Unplug the machine.  
Close the water tap.  
Apply to the nearest authorized service station.  
47  
 
METHODS OF  
ELIMINATION  
FAILURE  
PROBABLE CAUSE  
Insert the plug into the  
socket.  
It is unplugged.  
Your fuse is defected.  
Change your fuse.  
The electric power is  
off.  
Check the electric  
power.  
Start/pause button has Press the start/pause  
Your machine does not  
operate.  
not been pressed.  
button.  
Bring the program  
knob on the desired  
status.  
The program knob is in  
O(off) status.  
Shut the door properly.  
You should hear the  
click.  
The door is not shut  
properly.  
Water tap is closed.  
Open water tap.  
The water inlet hose  
may be bent.  
Check the water inlet  
hose.  
The water inlet hose is  
obstructed.  
The valve inlet filter is  
obstructed.  
Clean the filters of  
water inlet hose. (*)  
Clean the valve inlet  
filters. (*)  
Your machine does not  
receive water.  
Shut the door properly.  
You should hear the  
click.  
The door is not shut  
properly.  
The drain hose is  
obstructed or bent.  
Check the drain hose.  
The pump filter is  
obstructed.  
The clothes are not  
placed inside the  
machine in a well-  
balanced manner.  
Clean the pump filter.  
(*)  
Spread the clothes  
inside the machine in  
an orderly and well-  
balanced manner.  
Your machine is not  
draining water.  
The feet of your  
machine are not  
adjusted.  
Transportation screws  
are not removed.  
Adjust the feet. (**)  
Your machine is  
vibrating.  
Remove transportation  
screws. (**)  
(*)See the section concerning the maintenance and cleaning of your machine.  
(**)See the section concerning installations your machine.  
48  
 
METHODS OF  
ELIMINATION  
FAILURE  
PROBABLE CAUSE  
There is a small  
amount of clothes in  
the device.  
It does not prevent  
operation of the  
machine.  
Do not exceed the  
recommended quantity  
of clothes and spread  
your clothes in the  
machine in a well-  
balanced manner.  
Excessive amount of  
clothes are filled in the  
machine or the clothes  
are not placed in a  
Your machine is  
vibrating.  
well-balanced manner.  
Prevent your  
machine’s leaning on a  
tough place .  
Your machine touches  
a ripid object.  
Press the start/pause  
button.In order to stop  
the foam,dilute one  
table-spoon of softener  
in half liter of water and  
pour it in the detergent  
drawer.Press the  
start/pause button after  
5-10 minutes.Arrange  
the amount of the  
Too much detergent  
has been used.  
Excessive foam in the  
detergent drawer.  
detergent properly in  
the next washing  
process.  
Use only the  
Wrong detergent has  
been used.  
detergents produced  
for full automatic  
machines.  
Your laundry too dirty  
for the program you  
have selected.  
Select a suitable  
program. (see Table-1)  
The washing result is  
bad.  
The amount of  
detergent used is not  
sufficient.  
Use more detergent  
according to the  
detergent.  
49  
 
METHODS OF  
ELIMINATION  
FAILURE  
PROBABLE CAUSE  
Clothes exceeding the  
maximum capacity  
has been filled in your  
machine.  
Put the clothes in your  
machine in a manner  
not to exceed its  
maximum capacity.  
Use the amount of  
The washing result is  
not good.  
Your water may be  
hard.  
detergent according to  
the declaration of the  
detergent producer.  
Distribution of the  
clothes in your  
machine is not well-  
balanced.  
Spread the clothes  
inside the machine in  
an orderly and well-  
balanced manner .  
The end of the water  
drain hose is in a  
position too low  
according to the  
machine.  
The water is drained  
from the machine as  
soon as it is filled.  
Place the water drain  
hose in an appropriate  
height.(**)  
No failure. The water is  
at the lower part of the  
drum.  
No water is seen in the  
drum during washing.  
-
By calibrating your  
machine for “Rinsing”  
program,make an  
additional rinsing or  
eliminate the stains  
The pieces of some  
detergents which do  
not dissolve in water  
may stick to your  
There are residues of  
detergent on the  
clothes.  
clothes as white stains. After drying with the  
help of a brush.  
In the next washing  
These stains may be  
caused by oil,cream or maximum detergent  
ointment .  
operation, use the  
There are gray stains  
on the clothes.  
amount declared by  
the detergent producer.  
(**) See the section concerning instalations your machine.  
50  
 
METHODS OF  
ELIMINATION  
FAILURE  
PROBABLE CAUSE  
The unbalanced load  
control system will try  
to distribute your  
clothes in a  
homogenous manner.  
After your clothes are  
distributed, passage to  
spining process will be  
realized.In the next  
washing process,place  
your clothes into the  
machine in a well-  
balanced manner.  
No failure. The  
unbalanced load  
control may works in  
that way.  
The spining process is  
not done or starts with  
delay .  
SECTION 9: AUTOMATIC FAILURE DETECTION SYSTEM  
Your machine is equipped with systems which will both take the necessary  
precautions and warn you in case of any failure by controlling it self constantly  
during the washing processes.  
FAILURE  
CODE  
FAILURE  
INDICATOR  
PROBABLE  
FAILURE  
THE PROCESS  
TO BE DONE  
Shut the door  
properly so that  
you hear the  
click. If the  
problem  
persists, turn off  
the machine  
unplug and  
apply to the  
nearest  
The start/pause  
light blinks.  
The door is not  
shut properly.  
Err 01  
authorized  
service  
immediately.  
51  
 
FAILURE  
CODE  
FAILURE  
INDICATOR  
PROBABLE  
FAILURE  
THE PROCESS  
TO BE DONE  
Turn on the tap  
to the end.Water  
may be cut,  
check it.If the  
problem is still  
continuing,your  
machine will  
automatically  
stop after a  
while.Unplug  
your machine,  
turn off the tap  
and apply to the  
nearest  
The water level  
in your machine  
is below heater.  
The pressure of  
your water  
The program  
ready light  
blinks.  
Err 02  
supply may be  
low or locking.  
authorized  
service.  
Clean the pump  
filter.If the  
problem  
persists,apply to  
the nearest  
authorized  
The start/pause  
light and  
program ready  
light blinks .  
The pump has  
failed or the  
pump filter is  
obstructed.  
Err 03  
Err 04  
service.(*)  
Shut down your  
machine and  
unplug. Turn off  
your tap and apply  
to the nearest  
The program  
end light blinks .  
Communication  
error  
authorized service.  
(*) See the section regarding the maintenance and cleaning of your  
machine.  
52  
 
FAILURE  
CODE  
FAILURE  
INDICATOR  
PROBABLE  
FAILURE  
THE PROCESS  
TO BE DONE  
Shut down your  
The heater of your machine and  
The start/pause  
light and program  
end light blink.  
machine or the  
heat sensor has  
failed.  
unplug. Turn off  
your tap and apply  
to the nearest  
Err 05  
Err 06  
Err 07  
Err 08  
authorized service.  
Shut down your  
machine and  
unplug. Turn off  
the tap and apply  
to the nearest  
The program  
ready light and  
program end light  
blink.  
The motor has  
failed.  
authorized service.  
The program  
start/pause light,  
ready light and  
program end light  
stays on  
Shut down your  
machine and  
unplug. Turn off  
the tap and apply  
to the nearest  
Configuration  
error.  
permanently.  
authorized service.  
Shut down your  
machine and  
unplug. Turn off  
the tap and apply  
to the nearest  
The start/pause  
light,program  
ready light and  
program end light  
blink.  
Fault error  
authorized service.  
If the network  
voltage is lower  
than 150V or  
higher than 260V,  
your machine will  
automatically stop.  
When the network  
voltage is  
The program  
ready light and  
program end light  
stays on  
The network  
voltage is too high  
or too low.  
Err 09  
permanently.  
recovered, your  
machine will  
continue its  
operation.  
53  
 
SECTION 10: INTERNATIONAL WASHING SIGNS  
Washing  
temparature.  
Do not wash  
(hand wash)  
Lukewarm iron.  
Medium hot iron.  
Do not tumble  
dry.  
Hot iron.  
Drip dry.  
Do not iron.  
Dry flat.  
Hang to dry.  
Do not bleach.  
Handy to bleach.  
All of these are dry cleaning symbols. The letters are  
to instruct the cleaner what type of solvent to be used.  
Garments bearing these symbols should not be  
washed in your machine unless the label says  
otherwise.  
54  
 

Weslo Home Gym WLAW55075 User Manual
Whirlpool Air Conditioner ACM122XR0 User Manual
Whirlpool Clothes Dryer WGD9200SQ1 User Manual
Whirlpool Range EDP EDN User Manual
Whirlpool Washer Dryer WGD4700Y User Manual
Wolf Appliance Company Range DF604CF User Manual
Yamaha Speaker F12 User Manual
Zanussi Refrigerator 102314 User Manual
Zanussi Refrigerator 102338 User Manual
Zhone Technologies Network Card Network Device User Manual